Fomo Products Inc. F61050 HT - 300 7" Polymer Dispensing Unit

I worried that I was going to make a bad choice when I got these. These were the lower end of the pricing scale. Since using it I can never go back to using the regular non-gun foams. So far this gun has worked perfectly and it seems to be built well. Keep in mind that if you order a foam gun that it always needs to have a can attached to it. I did purchase some compressed cleaning cans but have not used them yet. This was a great investment and will save money in the end b/c there is hardly any wasted product.

Works very well, just as expected. I use spray foam for sculpting and for other applications and this gun does a fine job of shooting foam in a nice bead. Be sure to clean the end very well with solvent when done though, and best to leave a can of foam mounted to the gun when not in use, otherwise foam can harden in the barrel and tip and that's it for the gun.

It took me a year to use up my first can of foam: 30 or 40 small jobs, each of which would have required buying, and wasting, most of a can of the foam with the straw dispenser. This thing clearly saves a bunch of money. To keep it going: Keep the can on, don't take it off until it's empty, and when can is empty immediately put on a new one. Get The Acetone gun cleaner. When changing cans, spray clean the basket connection of the gun before mounting new can. After each use, thoroughly clean the tip with the acetone cleaner and a piece of a cotton towel. ( nail polish remover works if you don't have the can of cleaner) If not using the gun, spray out 3 egg sized gobs every week ( and then clean the tip) Every time you use the gun,snug up the plastic fittings that hold the nozzle on and the can on. They can get loose and let air in. This sounds like a lot but it isn't hard to do at all.

Worked fine the first time I used it. The second time I tried to use it, the foam was coming out very slowly. I turned the adjustment knob to increase the flow rate. When I squeezed the trigger, the adjustment knob popped off and flew across the room. Foam was now spraying out of the gun. I couldn't put the gun down without causing the pressurization gas to leak rapidly out of the can. So I had to carry it around until I could clamp it to something. The knob was too small to find. I accepted that there would be no way to use this gun again and unscrewed the can of foam so that I could use it with a better designed spray foam gun later. What kind of idiot designs something like this with a spring-loaded adjustment knob and no stopper to prevent it from being loosened too far or flying out?

It worked great for 2 cans of foam. After each use/can was empty I ran the gun cleaner throught it multiple times to ensure it wouldn't clog. The third time I did this I came back to it a few weeks later and it's completly clogged with hardened foam that I can't seem to clear up. Sucks cause i really liked the control it had and also have 4 unused cans that only work with the gun....

This gun is a dream to use! I have occasionally used the cans with the straw you can get a HD, and I hated them! The foam keeps oozing out, and gets all over the place. And you can only use the can once. This gun is SO MUCH BETTER than the single use canisters! When you stop pressing the trigger, the foam immediately stops coming out. You can control the size of the bead precisely. And you you can store the the remaining foam for later without everything clogging up. It makes foaming fun, almost addictive. Kind of like using a magic eraser. A couple of tips: - Get the cleaner to go with it. It is alcohol-based, and magically dissolves sticky, unhardened foam. You can either spray the cleaner like a can of spray paint, or mount it in the gun to clean the gun out. - Don't unscrew the trigger stop too far. I did once. It popped of when I pressed the trigger, and then the trigger wouldn't close, causing an uncontrollable stream of foam!

Works great. Allows precision control w little waste. So much better that using 16 oz bottles from HD & Lowes. No more flimsy plastic straws that you can force into gaps. The steel nozzle can be plunged between foam panels easily. But it, you won't regret it

This is a good Homeowner quality gun. Most of the gun is plastic with the exception of the nozzle which is metal. That hasn't seemed to effect the performance of the gun which so far has been flawless. Also keep in mind this gun sells for half what other guns are selling for. I've run 7 24 oz Great Stuff Pro cans through the gun without any problems at all. If I was a contractor using this all the time I would probably have went for an all metal and more expensive gun but for a homeowner I think you can't go wrong with this one. After using the gun cleans up nice with Acetone.